主题:CISCO常用配置命令及参数
-border-horizontal-spacing: 0px; -webkit-border-vertical-spacing: 0px; -webkit-text-decorations-in-effect: none; -webkit-text-size-adjust: auto; -webkit-text-stroke-width: 0px" class=Apple-style-span>
启动接口,分配IP地址
router>
router> enable router# router# configure terminal router(config)# router(config)# interface Type Port router(config-if)# no shutdown router(config-if)# ip address IP-Address Subnet-Mask router(config-if)# ^z
配置RIP路由协议:30秒更新一次
router(config)# router rip router(config-if)# network Network-Number <--通告标准A,B,C类网--> router(config-if)# ^z 配置IGRP路由协议:90秒更新一次
router(config)# router igrp AS-Number <-- AS-Number范围1~65535--> router(config-if)# network Network-Number <--通告标准A,B,C类网--> router(config-if)# ^z 配置Novell IPX路由协议:
Novell RIP 60秒更新一次 router(config)# ipx routing [node address] router(config)# ipx maximum-paths Paths <--设置负载平衡,范围1~512--> router(config)# interface Type Port router(config-if)# ipx network Network-Number [encapsulation encapsulation-type] [secondary] <--通告标准A,B,C类网--> router(config-if)# ^z 配置DDR:
router(config)# dialer-list Group-Number protocol Protocol-Type permit [list ACL-Number] router(config)# interface bri 0 router(config-if)# dialer-group Group-Number router(config-if)# dialer map Protocol-Type Next-Hop-Address name Hostname Telphone-Number router(config-if)# ^z 配置ISDN:
router(config)# isdn swith-type Swith-Type <--配置ISDN交换机类型,中国使用basic-net3--> router(config-if)# ^z 配置Frame Relay:
router(config-if)# encapsulation frame-relay [cisco | ietf ] router(config-if)# frame-relay lmi-type [ansi | cisco | q933a ] router(config-if)# bandwidth kilobits router(config-if)# frame-relay invers-arp [ Protocol ] [dlci ] <--配置静态Invers ARP表: router(config)# frame-relay Protocol Protocol-Address DLCI [ Broadcast ] [ ietf | cisco ] [ payload-compress | packet-by-packet ] --> <--设置Keepalive间隔: router(config-if)# keepalive Number --> <--为本地接口指定DLCI: router(config-if)# frame-lelay local-dlci Number --> <--子接口配置: router(config-if)# interface Type Port.Subininterface-Number [ multipoint | point-to-point ] router(config-subif)# ip unnumbered Interface router(config-subif)# frame-lelay local-dlci Number --> router(config-if)# ^z 配置标准ACL:
router(config)# access-list Access-List-Number [ permit | deny ] source [ source-mask ] <-- Access-List-Number 范围:1~99标准ACL;100~199扩展ACL;800~899标准IPX ACL;900~999扩展IPX ACL;1000~1099 IPX SAP ACL;600~699Apple Talk ACL--> router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z 配置扩展ACL:
router(config)# access-list Access-List-Number [ permit | deny ] [ Protocol | Protocol-Number ] source source-wildcard [ Source-Port ] destination destination-wildcard [ Destination-Port ] [ established ] router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z
就写到这里吧!不足之处请大家多多指教(⊙o⊙)哦
转自:[url=http://www.gobenet.net.cn]http://www.gobenet.net.cn[/url]
启动接口,分配IP地址
router>
router> enable router# router# configure terminal router(config)# router(config)# interface Type Port router(config-if)# no shutdown router(config-if)# ip address IP-Address Subnet-Mask router(config-if)# ^z
配置RIP路由协议:30秒更新一次
router(config)# router rip router(config-if)# network Network-Number <--通告标准A,B,C类网--> router(config-if)# ^z 配置IGRP路由协议:90秒更新一次
router(config)# router igrp AS-Number <-- AS-Number范围1~65535--> router(config-if)# network Network-Number <--通告标准A,B,C类网--> router(config-if)# ^z 配置Novell IPX路由协议:
Novell RIP 60秒更新一次 router(config)# ipx routing [node address] router(config)# ipx maximum-paths Paths <--设置负载平衡,范围1~512--> router(config)# interface Type Port router(config-if)# ipx network Network-Number [encapsulation encapsulation-type] [secondary] <--通告标准A,B,C类网--> router(config-if)# ^z 配置DDR:
router(config)# dialer-list Group-Number protocol Protocol-Type permit [list ACL-Number] router(config)# interface bri 0 router(config-if)# dialer-group Group-Number router(config-if)# dialer map Protocol-Type Next-Hop-Address name Hostname Telphone-Number router(config-if)# ^z 配置ISDN:
router(config)# isdn swith-type Swith-Type <--配置ISDN交换机类型,中国使用basic-net3--> router(config-if)# ^z 配置Frame Relay:
router(config-if)# encapsulation frame-relay [cisco | ietf ] router(config-if)# frame-relay lmi-type [ansi | cisco | q933a ] router(config-if)# bandwidth kilobits router(config-if)# frame-relay invers-arp [ Protocol ] [dlci ] <--配置静态Invers ARP表: router(config)# frame-relay Protocol Protocol-Address DLCI [ Broadcast ] [ ietf | cisco ] [ payload-compress | packet-by-packet ] --> <--设置Keepalive间隔: router(config-if)# keepalive Number --> <--为本地接口指定DLCI: router(config-if)# frame-lelay local-dlci Number --> <--子接口配置: router(config-if)# interface Type Port.Subininterface-Number [ multipoint | point-to-point ] router(config-subif)# ip unnumbered Interface router(config-subif)# frame-lelay local-dlci Number --> router(config-if)# ^z 配置标准ACL:
router(config)# access-list Access-List-Number [ permit | deny ] source [ source-mask ] <-- Access-List-Number 范围:1~99标准ACL;100~199扩展ACL;800~899标准IPX ACL;900~999扩展IPX ACL;1000~1099 IPX SAP ACL;600~699Apple Talk ACL--> router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z 配置扩展ACL:
router(config)# access-list Access-List-Number [ permit | deny ] [ Protocol | Protocol-Number ] source source-wildcard [ Source-Port ] destination destination-wildcard [ Destination-Port ] [ established ] router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z
就写到这里吧!不足之处请大家多多指教(⊙o⊙)哦
转自:[url=http://www.gobenet.net.cn]http://www.gobenet.net.cn[/url]